Перейти к содержимому

Фотография
- - - - -

Fastship 6.1.29


Сообщений в теме: 7

#1 MENTOR2005

MENTOR2005

    Рулевой 3-го класса

  • Основной экипаж
  • PipPipPipPip
  • 118 сообщений
  • Из:Черкассы
  • Судно: катамаран
  • Название: "Рассвет"

Отправлено 01 октября 2010 - 22:27

Кто может предложить нормальный дистрибутив проги без разводов. Я не такой навороченый юзер и никак не могу найти прогу.
  • 0

#2 larion

larion

    Рулевой 1-го класса

  • Основной экипаж
  • PipPipPipPipPipPip
  • 976 сообщений
  • Из:Петербург
  • Судно: gaffel schooner
  • Название: "ЛОСОСЬ"

Отправлено 01 октября 2010 - 22:51

http://rutracker.org...c.php?t=1754152 про безразводов не знаю, а тут с таблеткой рабочая версия есть
  • 0

#3 MENTOR2005

MENTOR2005

    Рулевой 3-го класса

  • Основной экипаж
  • PipPipPipPip
  • 118 сообщений
  • Из:Черкассы
  • Судно: катамаран
  • Название: "Рассвет"

Отправлено 01 октября 2010 - 23:33

вот именно про этот Торент я и имел ввиду. Такая хрень пока перичитаешь все и переделаешь, а потом выясняется Шаровары домоверсия. Так зачем все это.
  • 0

#4 larion

larion

    Рулевой 1-го класса

  • Основной экипаж
  • PipPipPipPipPipPip
  • 976 сообщений
  • Из:Петербург
  • Судно: gaffel schooner
  • Название: "ЛОСОСЬ"

Отправлено 01 октября 2010 - 23:59

http://isohunt.com/t...hip?tab=summary тут правда один раздающий (качаться будет год )

или

за бабло у производителя и проблем никаких

Сообщение отредактировал larion: 02 октября 2010 - 00:07

  • 0

#5 max_sonic

max_sonic

    Рулевой 3-го класса

  • Основной экипаж
  • PipPipPipPip
  • 192 сообщений
  • Из:Где то там
  • Судно: В процессе раздумий
  • Название: JeeMax

Отправлено 02 октября 2010 - 00:40

вот именно про этот Торент я и имел ввиду.
Такая хрень пока перичитаешь все и переделаешь, а потом выясняется Шаровары домоверсия.
Так зачем все это.


Все проверил, так как сам его скачивал и людям отправлял.......все замечательно работает под Win7, соответственно и под другие версии Винды должно замечательно работать.....
  • 0

#6 Байкал 71

Байкал 71

    Яхтенный капитан

  • Капитан
  • 2 479 сообщений
  • Из:г.Иркутск
  • Судно: различн
  • Название: Мария

Отправлено 02 октября 2010 - 04:51

Кто может предложить нормальный дистрибутив проги без разводов.
Я не такой навороченый юзер и никак не могу найти прогу.

А чем она отличается от 6.1.25 ?
  • 0

#7 max_sonic

max_sonic

    Рулевой 3-го класса

  • Основной экипаж
  • PipPipPipPip
  • 192 сообщений
  • Из:Где то там
  • Судно: В процессе раздумий
  • Название: JeeMax

Отправлено 02 октября 2010 - 20:17

А чем она отличается от 6.1.25 ?


Сообщение отредактировал max_sonic: 02 октября 2010 - 20:19

  • 0

#8 max_sonic

max_sonic

    Рулевой 3-го класса

  • Основной экипаж
  • PipPipPipPip
  • 192 сообщений
  • Из:Где то там
  • Судно: В процессе раздумий
  • Название: JeeMax

Отправлено 02 октября 2010 - 20:24

А чем она отличается от 6.1.25 ?



В первый раз файл почему то не прицепился......там на английском, кому надо, тот поймет......И сам файл попоробую еще раз прицепить и текст в тело вставлю....



FastShip TM 6 Release Notes
Please consult the Release Notes each time that you install a new release of FastShip, to get a summary of the changes and improvements that have been made.


Release 6.1.29
  • Added a new member called transform to the perl hydrostatics variable in order to allow macro writers to retrieve the floatation plane transformation resulting from a hydrostatics calculation.
  • Modified the commands copy-surface and mirror-surface so that if the original surface had trimming information, the new surface maintains the trimming information with the exception that trimming associativity is removed (i.e. all trim curves are unlinked). This exception is necessary since it is not known if the surfaces on which the trim curves depend were also copied or mirrored.
  • Modified the behavior of the command, write-model, to allow the keyword "current" when exporting hydro or area entities. The use of "current" informs FastShip that it does not need to update the hydrostatics calculations before exporting the necessary files. This is useful for certain FastShip Perl macros.
  • Modified the behavior of the command, write-2d-dxf, to include the coordinate axes for all 3 views in a "3-view" file export.
  • Modified the behavior of the command, flip-normal, to try to maintain the trimming logic such that the same portions of the surface are trimmed away.
  • Modified the command, create-planing-hull, to include two new shape factors. These are a bow roundness factor controlling the fullness of the bow shape and a transom width at deck factor allowing taper of the hull aft. Additionally minor modification were made to the planing hull algorithms to result in more realistic hull shapes. See the command reference for complete documentation.
  • Modified the logic for commands which internally interpret XML (e.g. load-model, add-model, measure-volume-ex) so that the user is informed and given a chance to continue in the unlikely event that the operations for setting internal locale fail. In the past the command would just fail and return.
  • Fixed a bug in an internal FastShip routine used to compute meshes of offset surfaces. The bug could cause a program crash for certain surfaces having somewhat "unusual" knot vectors by FastShip standards.
  • Fixed a bug in an internal FastShip routine used to project points onto a surface. The bug could cause a program crash for certain surfaces having somewhat "unusual" knot vectors by FastShip standards.
  • Fixed a dimensioning bug in metapoles.
  • Fixed a bug in hydrostatics calculations when using the "fixed trim" option in which the LCG was not being properly derived from the resultant LCB.
  • Fixed a bug in the command goodness-of-fit in which only 4 error bands (instead of the documented hard limit of 8 bands) could be used when the command was accessed from the Goodness of Fit dialog box.
  • A new version of the Hoops Graphical library (version 11) has been incorporated into FastShip in order to provide improved rendering performance and robustness.
  • Modified the FastLock utility to support both FastShip and VisualSMP locks.
Release 6.1.28
  • A new command, fit-surface-edge, was added which allows the user to perform a least squares fit between a polyline (offsets) and a candidate surface edge (including slope discontinuities). The new command was added to the NURBS menu.
  • A new command, create-process, has been added to allow the user to launch an external executable from FastShip.
  • Two new commands were added to FastShip related to images and texture mapping. The commands read-image inserts a gif file as an image into the current model. Currently there is no control over its location or size and it is not persisted in the pex file. This image always faces front as it is not associated with any geometry. The second new command, read-texture, allows reading a gif file as a texture map. The user specifies the name associated with the texture map which can then be applied to surface geometry via the set-surface-color command with the name of the texture as the surface color. Textures are not yet persisted and there is no easy way to display all currently loaded textures so you must remember what you called it. This functionality will be developed further in future releases using feedback from users.
  • Modified the FastShip hydrostatics command, measure-volume-ex, to correct some issues related to the option to insert a surface representing the resultant flotation plane. These issues were related to improper sizing of the waterplane surface when current units were not SI units and to properly transforming the flotation plane surface for upright (non-free float and non-rollover) hydrostatics calculations.
  • Changed the commands set-project and set-description commands to set the modified flag so that FastShip thinks the model has changed when either of these commands is invoked and will prompt the user to save the model before closing it.
  • Added a new optional argument, "nofilereset" to the read-surface command so that we can force it to act like it is adding a surface model to the current model as opposed to opening a new surface model. Specifically this argument has the effect of telling FastShip not to set the internal filename or the FastShip window title to the filename being added.. This addition was necessary because if a user reset the current system by selecting File/New and then adds a file (as opposed to opening it) we still want the system to think the model has not yet been named. If it was given the name of the added model, then if the user adds a second model to the first and saves, the original model file would get overwritten instead of prompting the user for a filename to save to as is now the case.
  • Fixed a bug in which opening a FastShip model by double clicking the file in Explorer had caused the window title to display the "Untitled" filename instead of the current model filename.
  • Fixed bug in the command associated with the y-coordinate spin button (y-nudge).
  • Modified how corner control points are displayed when they are frozen. If frozen they are now drawn as asterisks like internal control points.
  • Modified the command, set-false-colormap, to accept a new list argument defining minimum and maximum curvature magnitudes for the curvature map. Also modified the Surface Curvature dialog box to allow setting these values. While adding this new functionality, a problem which had existed in the fixed map indices was corrected. A legend was added to show the current curvature mapcolor range.
  • Modified the command, read-iges, to fix a bug which was introduced in an earlier modification related to reading entity 406 to obtain FastShip partnames.
  • Increased the size of FastShip's internal fixed-length strings by a factor of 4 to accomodate longer project names and project descriptions. This became necessary as a result of the generalization of the commands set-project and set-description to allow for very long stsrings.

  • 0



Ответить



  


Количество пользователей, читающих эту тему: 0

0 пользователей, 0 гостей, 0 скрытых пользователей